DXN-Q Indoor 7.2-40.5kV HV Live Display Device Voltage Indicator—Holes Sizes OF 92*44MM

• Specification
• Parameters

• DXN-Q Indoor 7.2-40.5kV HV Live Display Device Voltage Indicator—Holes Sizes OF 92*44MM

  Indoor high-voltage charged display device consists of three sensors and a display connected by a number line. Apply to the rated frequency 50Hz, rated voltage 40.5kV below the indoor high-voltage electrical equipment, both to reflect the circuit charged condition, but also with the electromagnetic lock with the realisation of mandatory locking switch handle, valves and so on. Powered display and forced locking are controlled by the same high-voltage signal, but the circuit system is independent of each other, do not interfere with each other, as long as the high-voltage circuits are powered, even if the display circuit and locking circuit failure at the same time, the electromagnetic lock is still in the locking state to prevent misoperation, accidentally enter the powered interval.

  This product is used to provide a switchgear equipment circuit voltage information at the installation status to the operator. As a result of its internal circuitry of low-power light-emitting element, which makes low power consumption, more stable performance and higher reliability. For the user test double-loop phase conveniently, indicator(recommend type) panel setting the end of the test phase, meanwhile the frame of indicator (recommend type) shell adopts front end removable. And the user can change the indicator without opening the indicator shell.

  Widely used for indooe 7.2, 12, 24, 40.5kV, frequency of 50Hz high voltage electrical equipment, and supporting the use of the voltage sensor, it can reflect the high voltage live situation, and voltage sensor support, but also to improve the anti-error performance ancillary products.

  Executive standard

  1.GB25081-2010 HV live display device(VPIS)

  2.DL/T533-93 condensation and pollution test condition for indoor AC HV switchgear and components

  3.IEC61958:2000 HV prefabricated switchgear assembly and control assembly-live displaying device

  Applying environment conditions

  1.Environment temperature: upper limit value not more than +40℃, lower limit value not lower than -25℃, special area not lower than -35℃.

  2.Sea level: no more than 1000m.

  3.Atmospheric conditions: RH daily average value not more than 95%, month average value not more than 90%, steam pressure daily average value not more than 2.2kPa, month average value not more than 1.8kPa.

  4.Environment condition: no obvious filth, no flammable, no explosive chemical etcing and salt fog place.

• Outline installation hole dimension

  

   

  Voltage indicator selection table

  

   

LYD103-T 6.6kV Live Monitor VPIS Voltage Presence Indicator

• Specification
• Parameter

• LYD103-T 6.6kV Live Monitor VPIS Voltage Presence Indicator

  This product is used to provide a switchgear equipment circuit voltage information at the installation status to the operator. As a result of its internal circuitry of low-power light-emitting element, which makes low power consumption, more stable performance and higher reliability. For the user test double-loop phase conveniently, indicator(recommend type) panel setting the end of the test phase, meanwhile the frame of indicator (recommend type) shell adopts front end removable. And the user can change the indicator without opening the indicator shell.

  Widely used for indoor 7.2,12,24,40.5kV, frequency of 50Hz high voltage electrical equipment, and supporting the use of the voltage sensor, it can reflect the high voltage live situation, and voltage sensor support, but also to improve the anti-error performance ancillary products.

   

  Executive standard

  GB25081-2010 HV live display device(VPIS)

  DL/T533-93 condensation and pollution test condition for indoor AC HV switchgear and components

  IEC61958:2000 HV prefabricated switchgear assembly and control assembly-live displaying device

   

  Applying environment conditions

  1.Environment temperature: upper limit value not more than +40℃, lower limit value not lower than -25℃, special area not lower than -35℃.

  2.Sea level: no more than 1000m.

  3.Atmospheric conditions: RH daily average value not more than 95%, month average value not more than 90%, steam pressure daily average value not more than 2.2kPa, month average value not more than 1.8kPa.

  4.Environment condition: no obvious filth, no flammable, no explosive chemical etcing and salt fog place.

• LYD103-T 6.6kV Live Monitor VPIS Voltage Presence Indicator

  Outline installation hole dimension

  

   

  

  Voltage indicator selection table

  

  Indoor HV live display device

DXN8D 7.2-40.5kV Indoor H.V. Alive Displaying Device–HOLES SIZES OF 100*70MM

• Specification
• Parameter

• DXN8D 7.2-40.5kV Indoor H.V. Alive Displaying Device–HOLES SIZES OF 100*70MM

  This product is used to provide a switchgear equipment circuit voltage information at the installation status to the operator. As a result of its internal circuitry of low-power light-emitting element, which makes low power consumption, more stable performance and higher reliability. For the user test double-loop phase conveniently, indicator(recommend type) panel setting the end of the test phase, meanwhile the frame of indicator (recommend type) shell adopts front end removable. And the user can change the indicator without opening the indicator shell.
  Widely used for indoor 7.2,12,24,40.5kV, frequency of 50Hz high voltage electrical equipment, and supporting the use of the voltage sensor, it can reflect the high voltage live situation, and voltage sensor support, but also to improve the anti-error performance ancillary products.

  Executive standard
  GB25081-2010 HV live display device(VPIS)
  DL/T533-93 condensation and pollution test condition for indoor AC HV switchgear and components
  IEC61958:2000 HV prefabricated switchgear assembly and control assembly-live displaying device

  Applying environment conditions
  1.Environment temperature: upper limit value not more than +40℃,lower limit value not lower than -25℃, special area not lower than -35℃.
  2.Sea level: no more than 1000m.
  3.Atmospheric conditions: RH daily average value not more than 95%, month average value not more than 90%, steam pressure daily average value not more than 2.2kPa, month average value not more than 1.8kPa.
  4.Environment condition: no obvious filth, no flammable, no explosive chemical etcing and salt fog place.

   

• Outline installation hole dimension

  

  

   

  Voltage indicator selection table

  

  

DXN8D INDOOR HV LIVE DISPLAY DEVICE–HOLES SIZES OF 92*44MM 

• Specification
• Parameter

• Summarize

  DSN Series live display indicator is used to provide a switchgear equipment circuit voltage information at the installation status to the operator. As a result of its internal circuitry of low-power light-emitting element, which makes low power consumption, more stable performance and higher reliability. For the user test double-loop phase conveniently, indicator(recommend type) panel setting the end of the test phase, meanwhile the frame of indicator (recommend type) shell adopts front end removable. And the user can change the indicator without opening the indicator shell.

  Widely used for indooe 7.2kV, 12kV, 24kV, 40.5kV, frequency of 50Hz high voltage electrical equipment, and supporting the use of the voltage sensor, it can reflect the high voltage live situation, and voltage sensor support, but also to improve the anti-error performance ancillary products.

   

  Executive standard

  GB25081-2010 HV live display device(VPIS)

  DL/T533-93 condensation and pollution test condition for indoor AC HV switchgear and components

  IEC61958:2000 HV prefabricated switchgear assembly and control assembly-live displaying device

   

  Applying environment conditions

  1.Environment temperature: upper limit value not more than +40℃,lower limit value not lower than -25℃, special area not lower than -35℃.

  2.Sea level: no more than 1000m.

  3.Atmospheric conditions: RH daily average value not more than 95%, month average value not more than 90%, steam pressure daily average value not more than 2.2kPa, month average value not more than 1.8kPa.

  4.Environment condition: no obvious filth, no flammable, no explosive chemical etcing and salt fog place.

• Outline installation hole dimension

  

  

  Voltage indicator selection table

  

   

  Indoor HV live display device